BMTF397-5 液晶显示模组规格书


源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 SPECIFICATION Revision:0.1 BMTF397-5 This module uses ROHS material CUSTOMER: Approved by: LIANCHEN LTD: Approved by: 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 Revision Record Rev No date Description V0.1 2015-1-28 Preliminary Specification Release 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 CONTENTS 1.General Description 2.Genreal Features 3. Block Diagram 4.Pin Description 5.Absolute Maximum Ratings 6. Electrical Specification 6.1 DC Characteristics 6.2 back blight circuit characteristics 7. Optical Specification 7.1 LCD optical Characteristics 7.2 Measurement system 8.Application Circuit 9.Initial Code 10.Reliability and inspection standard 10.1 Environment test(reliability test) 10.2 Ultraviolet radiation irradiation test 10.3 Mechanical test 10.4 Electron magnetic compatibility 11.Inspection standard 12.Caution and handing precaution 13.Installation in assembly 13.1 ESD(electro-static discharge) prevention 13.2 Dust and stain prevention 13.3 Installing lcd module to the enclosure 13.4 Mechanical forces 13.5 Operation 14 .Transportation and storage 15.Outline dimension Written by Checked by Approved by James James Lasley 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 COM 1. General Description The TF397-5 model is a color TFT LCM this module has a 3.97 inch diagonally measured active area with WVGA(480 horizontal by 800 vertical pixel array).each pixel is divided into red,green,blue dots which are arranged in vertical stripe and this module can display 16.7M colors. 2.General Feature Item Main Display Remark Display Mode Normally White, Tranmissive LCD Viewing direction 12 O’CLOCK Driving method a-si TFT active matrix Input signals MIPI I/F Outside dimensions 57.14mm(W)*96.85mm(H)*2.3mm(D) Active Atea 51.84mm(W)х86.4mm(H) Number of Pixels 480x(RGB)х800pixels Pixel Pitch 0. 108mm(W)х0. 108mm(H) Pixel Arrangment RGB vertical stripes Driver IC JD9161 Weight TBD 3. Block Diagram 480(RGB)X800 Driver SEG COM White LED 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 4.Pin Description No. Symbol Description 1 RESET Reset Pin 2 FMARK Tearing Effect pin.( Frame synchronizing signal) 3 IOVCC_1.8V Power supply for the I/O circuit. 1.65V ~ 3.3V 4 VCC_2.8V Power supply . 2.5V to 3.3V 5 VCC_2.8V Power supply . 2.5V to 3.3V 6 GND Ground 7 DATAP0 MIPI DSI : Data differential signal input pins. (Data lane 0) 8 DATAN0 9 GND Ground 10 CLKN MIPI DSI : CLOCK differential signal input pins. 11 CLKP 12 GND Ground 13 DATAN1 MIPI DSI : Data differential signal input pins. (Data lane 1) 14 DATAP1 15 GND Ground 16 LEDA Backlight anode 17 LEDA 18 NC No Connection 19 LEDK Backlight cathode 20 LEDK 21 GND Ground 22 X+(NC) NC 23 Y+(NC) NC 24 X-(NC) NC 25 Y-(NC) NC 5.Absolute Maximum Ratings Ta=25±5℃,Vss=GND=0 Item Symbol Ratings Unit Condition Operating power VDD -0.3~3.6 V Operating temperature TOPR -10~60 ℃ Storage temperature TSTR -20~70 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 6. Electrical Specification 6.1 DC Characteristics VSS=0V,VDD=2.85±0.05V,TOPR =-20~70℃ Item Symbol Conditio n Min. Typ. Max. Unit Supply power VDD 2.3 2.8 3.3 V Input high voltage VIH 0.7VDD - VDD Input low voltage VIL 0 - 0.3VDD Output high voltage V0H 0.8VDD - - Output low voltage V0L - - 0.2VDD Logic current consumption IDD - TBD TBD mA Current consumption during standby mode Is - 250 - uA 6.2 Backlight Circuit Characteristics(8 LEDs serial connection): Item Symbol Min Typ. Max. Unit Condition Operating voltage VLED 12 12.8 13.6 V ILED =40 mA Operating current ILED - 40 - mA - Back blight luminance (display white) - 5500 - cd/m2 ILED =40 mA BACKLIGHT CIRCUIT: LEDA1 LEDK1 LEDA2 LEDK2 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 7. Optical Specification Optical characteritics are determind after the unit has been on and stable for approximately 30 minutes dark environment at 25℃.the value specified are at an approximate distance 500mm from the lcd surface at a viewing angle and θ equal to 0 7.1 LCD Optical Characteristics Ta=25℃ parameter Symbol Condition Min Typ Max Unit Viewing Angle Φ=0° (3:00) θ Cr>10 - 70 - deg Φ=90° (12:00) - 70 - Φ= 180° (9:00) - 70 - Φ= 270° (6:00) - 60 - Contrast ratio Cr θ=0 Φ=0 300 500 - Respone time Tr+Tf - (35) - ms Surface Luminance Lv - (220) - Cd/m2 CIE(x,y) chromaticty RED X θ=0 Φ=0 0.629 0.649 0.669 Y 0.320 0.340 0.360 GREEN X 0.314 0.334 0.354 Y 0.585 0.605 0.625 BLUE X 0.129 0.149 0.169 Y 0.039 0.059 0.079 WHITE X 0.292 (0.312)0.332 Y 0.306 (0.326)0.346 7.2Measurement system (1)LCD Viewing Angle viewing angle is the angle at which the contrast ratio is greater than 10.the angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the lcd surface. 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 (2) Response time Response time is the time required for the display to transition from white to black (Rising time, Tr) and from black to white (Falling time, Tf).for additional information (3)Contrast Ratio(CR) Contrast Ratio(CR) is defined mathematically as: Surface Luminance with all white pixels Contrast Ratio= Surface Luminance with all black pixels Surface luminance is the center point across the lcd surface 500mm from the surface with all pixels displaying white. 8. Application Circuit Please consult our technical department for detail information. 9. Initial Code Please consult our technical department for detail information. 10.Reliability and inspection standard 10.1 Environment test(reliability test) Samples OK before testing Test item Test condition High temperature storage 70℃,120 hr Low temperature storage -20℃,120 hr High temperature operation 60℃,90 hr Low temperature operation -10℃,90 hr High temperature and high humidity operation 40℃,93 %RH,90 hr Thermal shock -10℃ 25℃ 60℃ 25℃ (30min) (5min) (30min) (5min) 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 20 cycle After completing the reliability tests.leave the samples under the room temperature and for the following inspection items: ① No clearly visible defects or deterioration of display quality allowed. ② No function-related abnormalities. ③ Connected parts still connecting tightly. ④ Display characteristics fulfil initial value,contrast ratio should be an least 30% of initial value. 10.2 Ultraviolet radiation irradiation test After Samples irradiated by ultraviolet tradiation,have no deterioration of display quality 10.3 Mechanical test 1)Vibration test Test item Test content In mobile telephone Reference mobile phone test standard Vibration test ( packed) frequence/acceleration 30Hz/2.5m/s2 direction X、Y、Z 3 direction time 30min respectively After completing the vibration tests,the samples have No function-related abnormalities or structure distortion . 2) Shock test Peak accelation m/s2 Pulseholding time ms Shock wave 300 11 Half sine wave or back peak sawtooh wave or trapeziform wave After completing the shock tests,the samples have No function-related abnormalities or structure distortion . 3)packing part drop test Test item Test content drop (packed in a box) height 80cm Drop mode Freedom drop Drop part 1 corner/3 arris/6 face,1time respectively After completing the packing part drop tests,the samples have no function-related abnormalities or structure distortion . 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 10.4 Electron magnetic compatibility Electrostatic withstanding voltage After air contact discharge(voltage:±8KV)and contact discharge directly(voltage:±4KV) test,the samples display ok ,and have noflicker、white screen、black screen、blue screen etc.abnormity display.。 11.Inspection standard No Item Criterion for defects Defect type 1 Black/white spot defect (in displaying) black/white spot definition y Φ= 2 )( yx + X 1. black/white spot defect (I) area size(mm) Acceptable number A B C Φ≤0.1 ignore ignore 0.10<Φ≤0.15 3 0.15<Φ≤0.25 2 Φ>0.25 0 2. black/white spot defect (II) area size(mm) Acceptable number A B C Φ≤0.3 ignore ignore 0.30<Φ≤0.50 5 (spacebetween is 20mm) 0.50<Φ≤1.00 3(spacebetween is 50mm) 1.00<Φ 0 Minor 2 Black/white line defect(in displaying) 1. black/white line defect (I) size(mm) Acceptable number L(length) W(width) area A B C 10<L0.03<W≤0.04 5 ignore 5.0<L≤10 0.04<W≤0.06 3 1.0<L≤5.0 0.06<W≤0.07 2 Minor 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 L≤1.0 0.07<W≤0.09 1 2. black/white line defect(II) size(mm) Acceptable L(length) W(width) area A B C 20<L0.05<W≤0.07 5 ignore 10<L≤20 0.07<W≤0.09 3 5.0<L≤10 0.09<W≤0.10 2 L≤5.0 0.10<W≤0.15 1 3 Blemish & foreign matters 1. dot (LCD) size(mm) Acceptable number area A B C Φ≤0.1 ignore ignore 0.10<Φ≤0.15 2 0.15<Φ≤0.25 1 0.25<Φ 0 2. blemish(on touch panle or between touch panel ane LCD) size(mm) Acceptable number AREA A B C Φ≤0.1 ignore ignore 0.10<Φ≤0.15 1 0.15<Φ 0 3.line(LCD/touch panle) size(mm) Acceptable number L(length) W(width) area A B C Ignore W≤0.02 5 ignore L≤3.0 0.02<W≤0.03 3 L≤2.0 0.03<W≤0.05 2 Minor 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 --- W>0.05 Treat with 4 Stain on LCD panel surface Stain which cannot be removed even when wiped lightly with a soft cloth or similar cleaning too are rejectable Minor 5 Rust in bezel Rust which is visible in the bezel is rejectable Minor 6 Defect of land surface contact Evident crevices which is visble are rejectable Minor 7 Parts mounting (1) failure to mount parts (2) parts not in the specification are mounted (3) polarith, for example,is reversed Major Major Major 8 Parts alignment (1) LSI,IC lead width is more than 50% beyond pad outline (2) Chip component is off center and more than 50% of the leads is off the pad outline Minor Minor 9 Conductive foreign (1) on open space(gnd,manual solder)solder ball is allowed up toΦ0.1mm(1EA). Major 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 matter (2) In case of shield space is allowed up toΦ0.2mm(1EA) 10 Faculty PWB correction (1) due to PWB copper foil pattern burnout,the patter is connected,using a jumper wire for repair;2 or more places corrected per PWB (2) short circuited part is cut,and no resist coating has been performed. Minor Minor Area definition LCD inspection area A:active area B:visible area C:outside of visible area(Invisible area after assembling) Visible Defect in area c,but it cannot affect product’s quality ,it is allowed . 12.Caution and handing precaution To avoid causing extended damages such as accidents resulting in injury or death,fire accidents,or social damages or social damages if the lcd module fails, Sunrise is always endeavor to maintain sufficient quality of the lcd module in process of designing and manufacturing. Please pay attention to the followings when you use this TFT LCD module. Safety 1) disassembling or modification do not disassemble or modify the modules.sensitive parts inside lcd module may be damaged,and dusts or scratches may mar the displays. 2) Breakage of lcd panel Do not ingest liquid crystal material,do not inhale this material,and do not permit this material to contact the skin,if glass of lcd panel id broken.if liquid crystal material contacts the skin,mouth or clothing,take the following actions immediately. In case contact to the eye or mouth,rinse with large amount of running water for more than 15 minutes.in case contact to the skin or clothing,wipe id off immediately and wash with soap and large amount of running water for moue than 15 minutes.the skin or closing may be damaged if liquid crystal material is left adhered.in case ingestion,rinse out the mouth well with water.after spewing uo by drinking large amount of water,get medical treatment. 3) Glass of lcd panel be careful with chips of grass that may cause injuring fingers or skin,when the glass is broken. C BA 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 4) Absolute maximum ratings Do not exceed the absolute maximum rating value under the worst probable condition caused by the supply voltage variation,input voltage variation,variation in parts’constants,environmental temperature,etc.,otherwise lcd module may be damaged. 5) power protection circuit employ protection circuit for power supply,whenever the specification specifies it. A suitable protection circuit should be applied,based on each system design. A fuae is not fitted to this module.therefore,without a suitable power-supply protection device,dust or partial circuit failure may cause overheating and/or burning,which may lead to injury. 6) Disposal Always comply with all applicable environmental regulations,when disposing of the lcd. 7) Edges of parts Be careful with edges of glass parts and metal frame,it may cause injuring. For designing the system,give special consideration that the wiring and parts do not touch those edges. 8) Recommended operating conditions Don’t exceed the recommended operation conditions in this specification.the performance and quality of the lcd module are warranted only when the lcd module is used within the recommended operation conditions.to use the lcd module over the recommended operation condition may have bad influence on the characteristics and reliability of the lcd module and may shorten the life of the lcd module. Therefore,when designing the whole set,not to beover the recommended operation conditions,you should fully take care of supply voltage change,characteristica of connection parts,serge of input-and-output line,and surrounding temperature. 13.Installation in assembly 13.1 ESD(electro-static discharge) prevention The circuit used in lcd module is very sensitive to ESD. The following caution should be taken when installing lcd module to an enclosure of the system in order to prevent damage of circuit used in lcd module. 1) Humidity Ambient humidityof working area is recommended to be higher than 50%(RH)in order avoid ESD. 2) Grounding -Preson handling lcd modules should be grounded with wirst band. -Tools like soldering iron and screw drivers and working benches should be grounded. -Grounded electro-conductive mats are recommended to be covered on the floor of working area and surface of working benched. -The grounding should be done through a resister of 0.5-1Mohms in order to prevent spark of ESD. 3) Be careful with touching metal portion of testing instruments in order to prevent unnecessary ESD. 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 4) Do not touch the electrode area of PCB and electrical parts like LSI,capacitor,connector pin,etc. 5) Ionizer Using ionizer(an antistatic blower)is recommended at working area in order to reduce electro-static voltage. 6) Removing protection film When removing protection film from lcd panel,peel off the tag slowly(more than one second)while blowing with ionizer toward the peelong face to minimize ESD which may damage electrical circuit. 13.2. Dust and stain prevention 1) Working area Reduce dust level in working area.especially the level of metal particle should be decreased,otherwise electrical circuit in lcd module may be damaged due to short circuit by metal particles. 2) Protection film Lcd module may be shipped with protection film on lcd panle in order to prevent from scratches and dust.it is recommended to remove the film at later process of assembling. 3) Wiping off dust on the panel When lcd panel becomes dirtu,wipe the panle surface off softly with absorbent cotton or another soft cloth.if necessary,breathe upson the panle surface and then wioe odd immediately and softly again.be careful not to spill organic solvents into the inside of lcd module.the solvents may be damaged by the solvents,so do not use any organic solvents for wiping off lcd panel. 4) Adhesive on lcd panel Be careful not to attach adhesive,grease.etc.,on lcd panel,because it is difficult to remove them without any damages on lcd panel. 5) Water spots on the panel Avoid the dewing or water condensation. Wipe off a spot or mist on lcd panel softly with absorbent cotton another cloth as soon as possible if happened,otherwiae discoloration or stain may be caused.and ,damage may occur if water penetrates the inside. 13.3.Installing lcd module to the enclosure 1) Installing lcd module to the enclosure Do not bend or twist lcd module even momentarily when the lcd module is installed into the system. Bending or twisting the lcd module may cause permanent damage. When the FPCis bent,the radius of FPC curvature must be more than value of recommendation to prevent bending and twisting forces from affecting the connection of FPC. Even temporary bending or twisting sometimes causes damage. 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 2) Interface Do not fasten screw,with catching interface FPC between lcd module and enclosure. This may cause bending of lcd module,or become the cause of a failure by damaging FPC. 13.4.Mechanical forces 1) Carry Hold the side of the plastic frame when you carry an lcd module by hand.if an lcd is carried using the FPC,it is likely to be damaged and the lcd will then malfunction.if you turn on the lcd with a broken FPC,it may cause smoke or burning. Protection (eg gloves)for fingers and hands is recommended to avoid injury by broken glass. 2) Strong mechanical shock Avoid strong mechanical shock.such as dropping the lcd from the work bench, or knocking it against a hard object. 3) Excessive forse Avoid applying excessive force,like pushing the surface of lcd panel.this may cause scratches or breakage of the panel,or a failure of the module. 4) Scratches on the panel Do not put heavy object such as tools,books,etc.,and do not pile up lcd modules. Be careful not to touch the surface of the polarzer with any hard and sharp object.these parts are so sensitive and can easily be sdcratched ,even if protected by a film. 5) Connector When inserting or disconnecting the connector into a conneceor of the lcd module,care should be taken to ensure that no strong external force is spplied to the connectot on the lcd module side. A strong external force applied to the connector or the FPC may damage that no part such as the FPC etc.should be caught between the case of the system and the module.make sure that the input signal connector of a module is securely and correctly connected to the connector on the system,not skewed,or incompletely connected. Inputting a signal etc.into the module with connectors incorrectly inserted may cause a circuit component or components to malfunction. 6) FPC When inserting or disconnecting the connector of the lcd module into a connector of the system,care should be taken to ensure that no strong external force is applied to the FPC on the lcd module side. A strong external force applied to the FPC may damage their connections. When assembling a module into a system,pay extra attention to ensure that no part such as the FPC etc.should be caught between the case of the system and the module. Make sure that the input signal connector of a module is securely and correctly connected to the connector on the system.not skewed,or incompletely connected.inputting a signal etc.into the module with connectors incorrectly inserted may cause a circuit component or components to malfunction.be careful not to pull or damage the FPC cables,to avoid mechanical damdge in FPC and connection part of FPC and cell. 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书 13.5. Operation 1) Power supply Power supplies should always be turned off during the assembly process. Do not connect or disconnect the power cables and connectors with power applied to lcd module.this may cause damage to the lcd module circuit. In operating module at the inspection process,and so on,the supply voltage and signals of driving decice must satisfy the sequence of power supplies and signals desctibed in this specifications. 2) Gas Do not expose the lcd module to any gas which is not normally contained in the atmosphere,it may cause mis-operation or defects. 3) Used for long term When a lcd module is used for a long term,the characteristics of lcd module might be changed and it may be out of the standard of optical specifications due to LED discoloration. LED has the characteristics of shifting optical characteristics by the long term use 14 .Transportation and storage 1) temperature do not store lcd module in a high temperature and high humidity condition,high than 35 and ℃ 70%(RH)for a long term ,meaning about one month or more,otherwise this may deteriorate the quality of the display.when you unavoidably store lcd modules for a long time,store between 0 and 35 a℃ nd with a relative humidty 70%or lower. 2) Low temperature Be careful not to leave it where the temperature is below specified storage temperature because the liquid crystal of the display panel may be damaged. 3) Ultra violet ray Store lcd module without exposure to direct sunlight or fluorescent lamps in order to prevent the module from strong ultra violet ray. 4) Cleanliness Keep the lcd module in clean place,because any dust,hard particle may damage the polarizer,or dust invades the inside of the lcd module. 5) Condensation of water The module should be stored under a condition where no condensation of water is allowed.it may cause mis-operation or defects.be especially careful not to make a module work under the condition that condensation of water appears. 6) Packing When you must re-package a lcd module after it has been removed from the original packaging,it is recommended to re-pack using the original package box and package material. 15.Outline dimension 源泰科技 Version: 0.1 2015-1-28 BMTF397-5 液晶显示模组规格书
还剩17页未读

继续阅读

下载pdf到电脑,查找使用更方便

pdf的实际排版效果,会与网站的显示效果略有不同!!

需要 2 金币 [ 分享pdf获得金币 ] 0 人已下载

下载pdf

pdf贡献者

清洁工

贡献于2021-01-15

下载需要 2 金币 [金币充值 ]
亲,您也可以通过 分享原创pdf 来获得金币奖励!
下载pdf